This is basically home-made siding made out of aluminum coil. Though it takes a while to make, it allows for a finish that will last for years as seen in the video. The first project shown had 12’ pieces at the tallest point in the gable. We’ve gone through many temperature changes and lots of 65 mph wind storms over the last decade. One builder I work with liked using this siding detail to separate gables from the horizontal siding. The nice part of this method is that there’s very little waste
0:48
This is basically home-made siding made out of aluminum coil. Though it takes a while to make, it allows for a finish that will last for years as seen in the video. The first project shown had 12’ pieces at the tallest point in the gable. We’ve gone through many temperature changes and lots of 65 mph wind storms over the last decade. One builder I work with liked using this siding detail to separate gables from the horizontal siding. The nice part of this method is that there’s very little waste
29.4K viewsApr 10, 2023
TikTokthesidingguy_
Bending Aluminum for Roof: Real-Time Tutorial with Van Mark Brake
0:55
Bending Aluminum for Roof: Real-Time Tutorial with Van Mark Brake
339.1K viewsFeb 18, 2023
TikTokthesidingguy_
When aluminum scraps start building up below my brake, I bend all the skinny strips into siding starters. Where I live, it’s against code to use vinyl starters unless it’s above flashing. We are allowed to use this metal Z-flashing as a vinyl siding starter since the siding has built in drain holes. They are diagramed in our province’s siding association’s best practice procedures. All of our suppliers sell a metal starter like this since this building code came into effect a few years back. I u
0:44
When aluminum scraps start building up below my brake, I bend all the skinny strips into siding starters. Where I live, it’s against code to use vinyl starters unless it’s above flashing. We are allowed to use this metal Z-flashing as a vinyl siding starter since the siding has built in drain holes. They are diagramed in our province’s siding association’s best practice procedures. All of our suppliers sell a metal starter like this since this building code came into effect a few years back. I u
12.8K viewsMar 14, 2023
TikTokthesidingguy_
DIY Sheet Metal Brake
8:22
DIY Sheet Metal Brake
1.5M viewsApr 22, 2016
YouTubeDonn DIY
DIY Home Made Press Brake
1:14
DIY Home Made Press Brake
133.7K viewsMar 8, 2017
YouTuberodneypopper666
HOW TO USE AN ALUMINUM BRAKE!
11:13
HOW TO USE AN ALUMINUM BRAKE!
17.5K viewsOct 30, 2020
YouTubeThe Hobby Farm Homestead
Homemade sheet metal brake
22:36
Homemade sheet metal brake
248.4K viewsOct 8, 2020
YouTubeFitzee's Fabrications
4:19
How to Build a Press Brake
2.1M viewsJan 13, 2012
YouTubethemetalschoolonline
17:57
HOW TO | Aluminum Brick Mold Casing
132.3K viewsNov 30, 2020
YouTubeVeteran Construction
8:04
How to Bend Aluminium Trim
33.9K viewsAug 30, 2018
YouTubeHome Maintenance Solution, Inc
5:55
How To EASILY Repair Holes In Aluminum
1.6M viewsJul 23, 2014
YouTubeelectronicsNmore
14:17
Building A Sheet Metal Brake (Bender) From Scrap
181.2K viewsJul 4, 2021
YouTubeJames Biggar
7:30
DIY Sheet Metal Bending Brake: No Welding
669.5K viewsSep 20, 2016
YouTubeJosh Charles
1:35
Do-it-yourself siding repairs
105.6K viewsAug 16, 2008
YouTubeFOX36
12:14
DIY Metal Brake for Bending Sheet Metal
2.6M viewsAug 4, 2016
YouTubeBrian Oltrogge
11:49
Press Brake Metal Bending Crash Course
180.7K viewsMay 10, 2019
YouTubeWoodchuckTinman
25:18
How to Build a 48 Inch Sheet Metal Brake
139.3K viewsFeb 10, 2021
YouTubeQuick Speed Shop
20:40
VSI - Vinyl Siding Institute Installer Trainee Event - Van Mark Brake & Trim-A-Table TAT60 Operation
10.3K viewsJul 1, 2021
YouTubeVan Mark Products
8:31
How to make a press brake
148.4K viewsOct 27, 2018
YouTubeFarmer Tyler Ranch
4:00
How To Repair and Install Aluminum Fascia Cover
131.6K viewsJan 13, 2021
YouTubeEveryday Home Repairs
15:54
Removing Aluminum Siding
358.4K viewsJun 2, 2011
YouTubeTheWXTV
18:23
VSI - Loading Coil / Bending Coil on Brake
59.8K viewsAug 3, 2020
YouTubeVan Mark Products
6:55
How to Choose a Sheet Metal Brake - Eastwood
50.6K viewsMay 11, 2021
YouTubeEastwood Company
24:44
How to custom bend flashings with a metal brake
7.4K viewsJul 28, 2019
YouTubeAustin Tischler
8:52
Tips for installing aluminum fascia (Everything Garage Part 7)
170K viewsAug 20, 2020
YouTubeHS Design Studio
16:18
How To Bend Metal Using a Brake | MY DIY
4K viewsJul 1, 2020
YouTubeMy DIY Builds
1:13
Siding removal with a screwdriver
29K viewsJan 7, 2021
YouTubeUncle Gary Builds
5:03
How To Prepare And Paint Aluminum Or Vinyl Siding
152.5K viewsJun 26, 2017
YouTubeShell Busey
2:56
How to Use a Metal Brake
198.3K viewsAug 13, 2016
YouTubePete Donnelly
6:10
How to Make a Homemade Sheet Metal Brake
236.5K viewsJan 11, 2019
YouTubeDIYFixMan
See more